Search found 90 matches
- Fri Oct 02, 2009 6:59 pm
- Forum: Operation
- Topic: No RPM, no advance, only TPS
- Replies: 10
- Views: 10259
I test the volts in pin1 and 3, but I try with the new MJLJ v4, the 12v in PIP signal is OK. My problem is the MJLJ 3 or not? but the engine no start with MJLJ 4, not spark, I change the VR wires polarity and nothing. only read the MAP sensor. Can you guide me to check my V3, bad solders can not see...
- Fri Oct 02, 2009 3:12 pm
- Forum: Q&A
- Topic: TPS on SU carb??
- Replies: 6
- Views: 8284
look my tps http://i317.photobucket.com/albums/mm399/Fabian1380/Engine%20A-Series/EDIS%20MJLJ%20Ignition/IMG_0993.jpg http://i317.photobucket.com/albums/mm399/Fabian1380/Engine%20A-Series/EDIS%20MJLJ%20Ignition/IMG_0995.jpg http://i317.photobucket.com/albums/mm399/Fabian1380/Engine%20A-Series/EDIS%2...
- Fri Oct 02, 2009 3:03 pm
- Forum: Operation
- Topic: No RPM, no advance, only TPS
- Replies: 10
- Views: 10259
Thanks Brent. I test the lines between the pin1 EDIS module and ground I have 1.15v abd running 0.75v. I check the line in the EDIS and the MJLJ the same volts Pin3 EDIS 0.01v and ground show me 0.01v and running 0.2v. I install a new line in PIP signal and the same volts I check all the lines are o...
- Thu Oct 01, 2009 9:39 pm
- Forum: Operation
- Topic: No RPM, no advance, only TPS
- Replies: 10
- Views: 10259
No RPM, no advance, only TPS
Hi. I have a MJLJ v3.0 for 2 years in my mini, no problem, now I pait the car and the shift light not work, the laptop only show me the TPS, the rpm and ignition advance not work, I check the lines are OK, I change the VR sensor and the EDIS module, the same problem. The MJLJ work fine, but now I do...
- Tue Sep 22, 2009 1:24 am
- Forum: Powered by Megajolt Gallery
- Topic: Hi People, its my mini...
- Replies: 5
- Views: 7947
- Tue Aug 11, 2009 2:03 am
- Forum: Q&A
- Topic: red or blue?
- Replies: 1
- Views: 2378
red or blue?
what is the difference with red o blue?
- Sun Jun 07, 2009 3:11 am
- Forum: Q&A
- Topic: Pocket spark
- Replies: 2
- Views: 3578
The two pieces of software on that page were for 'VRSSIM VR sensor simulator for Ford EDIS ignition module. This software generates a simulated 36-1 signal on the PC parallel port, to allow bench testing of the full EDIS / MJLJ system.' http://www.heggs.co.uk/vrssim/ and 'Pocket Spark Configure &am...
- Sat Jun 06, 2009 9:35 pm
- Forum: Q&A
- Topic: Pocket spark
- Replies: 2
- Views: 3578
Pocket spark
the link is broken¿?
http://www.autosportlabs.net/MJLJ_3rd_Party_Software
http://www.autosportlabs.net/MJLJ_3rd_Party_Software
- Thu May 28, 2009 8:54 pm
- Forum: Operation
- Topic: Error Message on Firmware Upgrade
- Replies: 15
- Views: 11641
- Thu Nov 20, 2008 2:43 pm
- Forum: Operation
- Topic: Noise/Interference caused by EDIS/MJ - Any ideas
- Replies: 10
- Views: 10243
Hi I have a problem with the tacho, the tacho is crazy, show me everyting, I used the 15v zener and 1 1N4007, I take 1 signal to the coil, my tacho is for 4 cil and 2 cilinders, I configured to 2 cilinders the tacho works fine short time. My question is: I need a filter condenser or not?, my problem...
- Tue Nov 18, 2008 4:44 pm
- Forum: Powered by Megajolt Gallery
- Topic: My mini
- Replies: 21
- Views: 36422
Nice work. Did you do alot of the work yourself? all the work done on my car this done for me, everything!. looks like you fabed up an extra oil sump plug to go on the back of your gearbox?? I fitted one as well, but not quite sure how i'm going to get at it come an oil change as its behind my lcb,...
- Mon Nov 17, 2008 4:49 pm
- Forum: Powered by Megajolt Gallery
- Topic: My mini
- Replies: 21
- Views: 36422
Very good work....your finger is not good..
have you a photobucket? or flickr or web to see your car?
Look here my work
have you a photobucket? or flickr or web to see your car?
Look here my work
- Mon Nov 17, 2008 4:39 pm
- Forum: Powered by Megajolt Gallery
- Topic: My mini
- Replies: 21
- Views: 36422
- Mon Sep 08, 2008 3:44 pm
- Forum: Future Upgrades
- Topic: coil Per cylinder
- Replies: 18
- Views: 56114
- Mon Aug 18, 2008 5:14 pm
- Forum: Future Upgrades
- Topic: MJLJ V4 + Knock sensor = possible good idea
- Replies: 30
- Views: 68408
Hi
check this and comments.
if the auxiliary input support 0-5v, this circuit can work with MJLJ?
http://www.msextra.com/manuals/MS_Extra ... .htm#knock
http://www.viatrack.ca/
check this and comments.
if the auxiliary input support 0-5v, this circuit can work with MJLJ?
http://www.msextra.com/manuals/MS_Extra ... .htm#knock
http://www.viatrack.ca/