Search found 693 matches
- Sat Feb 19, 2011 9:58 pm
- Forum: Operation
- Topic: Another can't read cylinder count problem.
- Replies: 7
- Views: 6087
- Sat Feb 19, 2011 4:09 pm
- Forum: Installation
- Topic: Firing Order
- Replies: 4
- Views: 9926
- Sun Feb 06, 2011 5:42 pm
- Forum: Hard Rev Limiter
- Topic: Rev limiter for my bike - i need infos and help
- Replies: 1
- Views: 10568
- Sun Feb 06, 2011 5:27 pm
- Forum: Operation
- Topic: GM Temperature Resistance Calibration
- Replies: 2
- Views: 4598
Hi Healey and welcome to the forum. Sounds like you have an interesting mix there. You will have to get some pics up when you have finished. I would believe the GM and ford CTS (Coolant temperature sensors) would be very similarly calibrated. You could try the Ford calibration. If not it maybe a cas...
- Sun Feb 06, 2011 5:05 pm
- Forum: Installation
- Topic: missing tooth
- Replies: 1
- Views: 3229
Hi there clubbie70 and welcome to the forum. The triggerwheel should be installed as per the instructions at http://www.autosportlabs.net/MJLJ_V4_vehicle_installation_guide#Crank_timing_wheel_and_sensor_installation Basically count 9 teeth from the VR sensor with the engine at TDC. It doesn't really...
- Sun Feb 06, 2011 5:01 pm
- Forum: Installation
- Topic: EDIS problems
- Replies: 3
- Views: 6198
- Sun Feb 06, 2011 5:00 pm
- Forum: Installation
- Topic: Hard rev laptop
- Replies: 1
- Views: 3792
- Fri Feb 04, 2011 7:17 pm
- Forum: News and Announcements
- Topic: Ignition driver board
- Replies: 14
- Views: 38098
- Sat Jan 22, 2011 8:33 pm
- Forum: Installation
- Topic: B*gger!!!
- Replies: 8
- Views: 7291
- Sat Jan 22, 2011 8:25 pm
- Forum: Operation
- Topic: MAP Operation
- Replies: 4
- Views: 4543
Ahh, slightly different to what i suggested. I thought about using the electronic signal produced by each of the four MAP sensors to produce a single signal to the megjolt, instead of using a four way joiner and a smoothing reservoir. So each runner would be mechanically separated but electronically...
- Sat Jan 22, 2011 7:38 pm
- Forum: Installation
- Topic: Vacuum/MAP feed?
- Replies: 9
- Views: 8179
Something like this. This is the CIS injection model. The carb models have a similar one on the right hand side of the manifold. This T piece is also a valve to store vacuum escaping from the Vacuum reservoir of the brake servo when in low vacuum MAP (possibly engine stall) and requiring to still br...
- Sat Jan 22, 2011 7:21 pm
- Forum: Operation
- Topic: Runtime error - Microsoft isual C ++ Runtime Library
- Replies: 10
- Views: 9457
Personally I believe it to be a hardware issue with the USB adaptor or a software issue with the computers/usb adaptor drivers at this time. If you can, try to get hold of a desktop PC (these normally have dedicated serial ports) to confidence test the megajolt to make sure it can communicate with s...
- Sat Jan 22, 2011 6:24 pm
- Forum: Operation
- Topic: Runtime error - Microsoft isual C ++ Runtime Library
- Replies: 10
- Views: 9457
- Sat Jan 22, 2011 6:15 pm
- Forum: Assembly
- Topic: New main plug and terminals in uk
- Replies: 2
- Views: 11791
- Sat Jan 22, 2011 6:13 pm
- Forum: Q&A
- Topic: What software do I need for megajolt V 3 ???
- Replies: 8
- Views: 8650
Hi Cornelius,
Sorry for the late reply. You can find V3 downloads here http://www.autosportlabs.net/MJLJ_V3_Downloads
Hope this helps and isn't too late
Ryan
Sorry for the late reply. You can find V3 downloads here http://www.autosportlabs.net/MJLJ_V3_Downloads
Hope this helps and isn't too late
Ryan