Search found 10 matches
- Wed Feb 22, 2017 5:47 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
- Wed Feb 22, 2017 5:33 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
I was going to do just this. Can you tell me what port the signal should be on in the unit? I noticed that the #1 connection had a wire going somewhere and there was a signal reading on it that was about what the tach should be but didnt vary with acceleration. Dont think it was wired quite right an...
- Tue Feb 21, 2017 9:28 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
- Tue Feb 21, 2017 9:15 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
- Tue Feb 21, 2017 8:47 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
Analogs all set at linear then a scaling factor - as above. Yeah! RPM not working right yet tho. If the sample rate is disabled, gets a reading about twicw what it shoud be and returns to 6 places after the decimal pt. CHangedd channel mode to try them all, no change, and pulse per rev changed from ...
- Tue Feb 21, 2017 8:34 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
- Tue Feb 21, 2017 7:51 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
Hi Brent - holiday yesterday but took the following info today. Dashboard view for fuel Connected to analog port. sample 1hz, linear box checked and default of 1.0, preision of 1 and it reads ok, guage reads about 3/4 full, actual read about 4.5, tank size is 13 gals so it appears to be off about 3x...
- Sat Feb 18, 2017 7:02 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
This is the process I have been using and I also changed the pulses per revolution to 4, did write the change, but didnt make any difference. I also closed the program and re-started it. The car is in the shop and not available over the weekend but you probably have better things to do! I'll write d...
- Sat Feb 18, 2017 1:41 am
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
Thanks for the speedy reply! First off, I didnt do the elec. on the car or connections to the box but it was done by a competent person. Not to say they are correct! This is on a 2002 Toyota MR2 if that is any info. Analogs are 1:fuel, 2: oil press, 3:oil temp 4: coolant temp. (5,6,7 not used) These...
- Fri Feb 17, 2017 10:19 pm
- Forum: Sensors
- Topic: VERY basic set up info for new user
- Replies: 16
- Views: 22628
VERY basic set up info for new user
Race Capture Pro2: Unit installed and connected to laptop.Not able to configure the RPM or analog input channels to get correct read outs on the Dashboard display. Tried all kinds of combos. Also, for RPM read out - it appears that the WRite function isnt updating on the unit itself. Was apparent wh...