Search found 11 matches
- Wed Jul 11, 2012 11:03 pm
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
Wiring Diagram
Here is a diagram of the system I built with 2 MSD DIS-4 modules. I am completing a digram with 1 DIS-4 module. In either case the same problem occurs.
- Tue Jul 03, 2012 1:18 pm
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
- Mon Jul 02, 2012 7:42 pm
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
I likely will not get around to working on this until October. I returned the car to HEI so I can run my Autocross events. I looked at the car again today and the problem is still finding a suitable mount. The two coil packs tend to be heavy when trying to mount them. Thanks for your help and opinio...
- Mon Jul 02, 2012 1:50 am
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
My original build was a mockup of typical EDIS with 2 coil packs. I installed the MegaJolt to handle the timing as the Corvette ECU EST signal would not advance the timing. I was not satisfied with the mounting of the coil packs because I was not able to fabricate an acceptable mount that I felt wou...
- Sun Jul 01, 2012 4:39 pm
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
Although the resolution of the picture is not clear, the two harnessess coming from the top of the page next to each coil are in fact the factory wiring. You can see the actual instructions here from MSD: http://www.msdignition.com/WorkArea/DownloadAsset.aspx?id=15032386155 This is a PDF document: P...
- Sun Jul 01, 2012 2:38 pm
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
- Sun Jul 01, 2012 12:36 am
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
Thanks for verifying my understanding of the EDIS system. I could not get JD at MSD to understand that point. On an ocscilloscope I have four good signals from the EDIS module to the DIS-4 that do not show any problem when I get the miss. The frequency changes when I raise the rpm which confirms tha...
- Fri Jun 29, 2012 2:34 pm
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
I spoke with JD at MSD. He seems to think the Megajolt is causing the problem. I am sending him the Megajolt, EDIS Module and a wiring diagram for them to test my setup. He claims the Megajolt does not have the power to run the coil drivers. My understanding is the Megajolt provides the SAW/SPOUT si...
- Mon Jun 18, 2012 10:45 pm
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
Verify No Start
I verified today that the EDIS Module will not fire 8 coils. Hence the need for the MSD DIS-4. I will be returning the car back to HEI because autocross season has begun. I will probably not get around to trying to make the EDIS work until October. Although my CKP signal looked good on the Ocscillos...
- Mon Jun 18, 2012 12:05 am
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
Original build was with two stock coil packs. The engine ran fine but I did not run it at 3800rpm because the wiring was only mocked up. I did not like the way the coils mounted where the distributor had previously been located. When I changed to 8 stock COP coils the engine would not start. When I ...
- Sun Jun 17, 2012 12:33 am
- Forum: Installation
- Topic: Megajolt or MSD problem on EDIS Corvette
- Replies: 19
- Views: 25994
Megajolt or MSD problem on EDIS Corvette
:?: This is a copy of a post that I made to the MSD Forum. Is there any way that the Megajolt running the default MAP could cause this problem? I am waiting for a serial to USB connector to arrive in order to use the Megajolt software. The MSD Tech Line leaves much to be desired. I spoke to a disint...