Gents
Thanks for the replies. I've changed to a different bracket and so far so good, no further problems. Thanks for the great advice
Cheers
Nick
Search found 11 matches
- Tue Dec 11, 2012 8:44 am
- Forum: Operation
- Topic: Ignition cuts out intermittently
- Replies: 4
- Views: 5458
- Sat Dec 08, 2012 9:18 am
- Forum: Operation
- Topic: Ignition cuts out intermittently
- Replies: 4
- Views: 5458
Ignition cuts out intermittently
Hi I've been running MJLv3 for a while with no problems. In the last couple of weeks the car has developed a problem where the ignition cuts out whilst driving along for a few seconds, stone dead for a bit followed by massive backfire once the exhaust sensor gets hold of the unburnt fuel then it com...
- Tue Oct 02, 2012 10:20 am
- Forum: Assembly
- Topic: TPS to MAP hardware conversion
- Replies: 6
- Views: 17610
- Sat Jan 22, 2011 8:31 am
- Forum: Assembly
- Topic: TPS to MAP hardware conversion
- Replies: 6
- Views: 17610
- Fri Jan 21, 2011 2:22 am
- Forum: Assembly
- Topic: TPS to MAP hardware conversion
- Replies: 6
- Views: 17610
Hi Brent Thanks for getting back to me. The MAP installation looks good but i still can't reflash the unit. After following the instructions i get the following message: can't open input file mjlJunior_V4.0.2.s19 If i run : C:\mjlJunior_firmware_V4.0.2\hco8sprg.exe COM11 then things look kind of pro...
- Thu Jan 20, 2011 10:34 am
- Forum: Assembly
- Topic: TPS to MAP hardware conversion
- Replies: 6
- Views: 17610
TPS to MAP hardware conversion
HI I have a pre-assembled TPS MJLV4 and am converting to MAP; have installed the map sensor the two capacitors and the resistor in the MAP section of the board and have removed R3 from the TPS section of the board to disable TPS. The problem i have is that when i go into the configurator set the con...
- Mon Oct 25, 2010 5:00 am
- Forum: Operation
- Topic: Zetec Starting Problem
- Replies: 7
- Views: 8151
Small update for anyone with a similar setup/problems: Removed tamper seals and adjusted the idle mixture screws 1.5 turns out from lightly seated posn Replaced crank sensor (Old one suffered a little damage from contact with a toothed wheel on a Xflow setup) Fired up first turn of the key, idled we...
- Tue Aug 24, 2010 10:22 pm
- Forum: Operation
- Topic: Zetec Starting Problem
- Replies: 7
- Views: 8151
Thanks Ryan All good suggestions i'll get the timing light out to confirm all is well with the igniton; i suspect it is as i was running this ignition set up with a different engine (2D Xflow) in the car with no complaints for about 6 months having got rid of the ballast resistor. The carbs are unmo...
- Mon Aug 23, 2010 11:50 pm
- Forum: Operation
- Topic: Zetec Starting Problem
- Replies: 7
- Views: 8151
- Mon Aug 23, 2010 10:44 pm
- Forum: Operation
- Topic: Zetec Starting Problem
- Replies: 7
- Views: 8151
Zetec Starting Problem
Hi I've just finished installing a 1.8 Blacktop Zetec in a MK2 Escort running MJLJnrV4 (TPS) and a set of ZX9R Carbs on an otherwise standard motor. I am using the 'rolling road map' from this forum as a starting point. I have been able to start the engine a couple of times and once running it idles...
- Sat Jan 09, 2010 10:11 am
- Forum: Operation
- Topic: Can't connect to Jolt with Vista
- Replies: 24
- Views: 43324
HI Same problem for me too: MJLJnr V4 purchased assembled Dell vista laptop Prolific usb to serial COM ports correct in config/device manager 'Timeout cylinder count' is the error message Configurator freezes and needs to be shut-down No communication using telnet prog (Unless i'm not using it corre...