Search found 42 matches
- Sun Jan 26, 2014 4:01 pm
- Forum: Q&A
- Topic: controlling a water metahnol injection setup
- Replies: 1
- Views: 3154
controlling a water metahnol injection setup
Who has done this with a MJ? I want to bring on water/meth injection pump at around 2500 rpm, so using a shift light should work ok. but I only want it to operate when I have boost so it doesn't work on deceleration. I presume i would need an external boost switch wired in as the MJ doesn't have boo...
- Sat Jun 01, 2013 2:36 pm
- Forum: Q&A
- Topic: MAP sensor issue, help
- Replies: 1
- Views: 3300
- Fri May 31, 2013 8:33 pm
- Forum: Q&A
- Topic: MAP sensor issue, help
- Replies: 1
- Views: 3300
MAP sensor issue, help
I bought an external 2 bar map sensor to convert from TPS as running boost now but when connected and powered the KPA is at 30.. this should read 100?? Any ideas why im getting 30 KPA.? Engine not running btw.
many Thanks!
many Thanks!
- Thu Mar 21, 2013 10:03 am
- Forum: Q&A
- Topic: wiring in a hidden kill switch
- Replies: 1
- Views: 3087
wiring in a hidden kill switch
Hi can i just put a 2 way latching switch on the power out to coil wire from a megajolt with rev limiter to stop the car being started or will it still operate in limp home mode? I understand that without rev limit the MJ and edis 4 take a common 12v supply but the rev limit version has the power to...
- Mon Apr 30, 2012 8:18 pm
- Forum: Q&A
- Topic: Changing from tps to map
- Replies: 2
- Views: 5756
- Sun Apr 29, 2012 11:58 pm
- Forum: Q&A
- Topic: Changing from tps to map
- Replies: 2
- Views: 5756
Changing from tps to map
I supercharged my engine and need to run a MAP setup now. I know I can get the stand alone map sensor with 3 pin connector on it.. is it as simple as hooking the tps wires over??? I presume not?? what do I need to do?
Tried a search but there were so many results that are not related!
Many Thanks!
Tried a search but there were so many results that are not related!
Many Thanks!
- Sun Jan 08, 2012 1:44 pm
- Forum: Q&A
- Topic: Changing from TPS to MAP for boosted application
- Replies: 5
- Views: 6898
Cheers thanks, will make my way over to TW.. BTW how will the ignition map work then? will the upper half of the ignition table be a vacumm (-) and the lower half boosted (+).. never played with ignition timing on a blown engine before. any pointers for a novice would be greatly appreciated. ETA- my...
- Sun Jan 08, 2012 12:36 pm
- Forum: Q&A
- Topic: Changing from TPS to MAP for boosted application
- Replies: 5
- Views: 6898
Trying something different, its an mild NA engine so a little boost will give a decent result. You have the external MAP for sale?? Is it just a case of disconnecting the TPS wires inside the MJ main board and feeding the new wires from MAP in to its place?? I had considered swapping the unit for a ...
- Sun Jan 08, 2012 12:57 am
- Forum: Q&A
- Topic: Changing from TPS to MAP for boosted application
- Replies: 5
- Views: 6898
Changing from TPS to MAP for boosted application
I now have a blower on my megajolted engine, currently running tps, considering changing to MAP for obvious reasons. can the map model handle boost?? how much? sorry if this has been covered before, search is throwing up sooooo many threads.. thanks in advance http://i661.photobucket.com/albums/uu33...
- Tue Nov 16, 2010 8:51 pm
- Forum: Installation
- Topic: Where to get edis coil pack terminals
- Replies: 2
- Views: 5237
Where to get edis coil pack terminals
Where can I get crimp on HT lead connectors/terminals for my current HT leads??
Heres what I need-
http://www.boostengineering.net/v/vspfi ... 0wires.pdf
But in the UK... Shipping makes it too expensive
Many Thanks
Heres what I need-
http://www.boostengineering.net/v/vspfi ... 0wires.pdf
But in the UK... Shipping makes it too expensive
Many Thanks
- Tue Apr 27, 2010 11:21 am
- Forum: Operation
- Topic: Afr/lambda datalogging
- Replies: 3
- Views: 3659
- Sun Apr 25, 2010 10:18 pm
- Forum: Operation
- Topic: Afr/lambda datalogging
- Replies: 3
- Views: 3659
Afr/lambda datalogging
With the price of a rolling road (+ a bit extra) I was gonna buy a Afr setup and do some datalogging and tune myself... I know the rolling road will be the simple one off job done option but.... sack that! I'm always changing this and that with me carbs and stuff. Was gonna go an lc 1 but they are q...
- Sat Apr 24, 2010 8:57 pm
- Forum: Assembly
- Topic: Connector spades
- Replies: 8
- Views: 19540
- Sat Apr 24, 2010 8:19 pm
- Forum: Assembly
- Topic: Connector spades
- Replies: 8
- Views: 19540
- Sat Apr 24, 2010 8:12 pm
- Forum: Assembly
- Topic: Connector spades
- Replies: 8
- Views: 19540