Search found 347 matches
- Sun Feb 04, 2007 10:45 pm
- Forum: Installation
- Topic: Spark plug leads..
- Replies: 16
- Views: 13941
Accel makes nice and cheap
Accel makes nice and cheap plug wires: http://www.accel-ignition.com/CatalogsList.aspx?BrandID=3 But I think you want to know how to make aftermarket plug wires fit those FORD coil packs? In my previous application I took parts of old wire sets, and installed onto new wires, and it worked perfectly....
- Sat Feb 03, 2007 11:10 pm
- Forum: Assembly
- Topic: timing out connection error
- Replies: 8
- Views: 7566
Hi Brent. I have plenty of
Hi Brent. I have plenty of experience making communications API work over a cheap USB-2-serial. Last year I spend quite some time making my serlcomm.dll and mjctrl.dll working properly. Currently those libraries are so well rounded that they are guaranteed to work, as long as adapter is properly ins...
- Fri Feb 02, 2007 3:32 pm
- Forum: Installation
- Topic: Fitting...
- Replies: 2
- Views: 3140
Hey, can I e-mail you? What
Hey, can I e-mail you?
What is your e-mail address? Tried your site, but no luck there.
What is your e-mail address? Tried your site, but no luck there.
- Thu Feb 01, 2007 6:55 pm
- Forum: Future Upgrades
- Topic: Datalogging EEC IV... any insight???
- Replies: 7
- Views: 10524
Please pass on to the MARK
Please pass on to the MARK VIII community.
- Thu Feb 01, 2007 4:07 pm
- Forum: Future Upgrades
- Topic: Datalogging EEC IV... any insight???
- Replies: 7
- Views: 10524
Well, I have a good news for
Well, I have a good news for you, installation of Megajolt on your car involves these 3 steps: 1) Connect two wires from Megajolt to EDIS-8 2) Provide +12 and -12 V power for Megajolt 3) Attach vacuum to Megajolt Done! Then you connect your laptop and it will run like a beauty... So, you will need t...
- Thu Feb 01, 2007 1:43 pm
- Forum: Future Upgrades
- Topic: Datalogging EEC IV... any insight???
- Replies: 7
- Views: 10524
Hi there. I had a crown vic
Hi there. I had a crown vic and now a gt running Megajolt and Megasquirt. The combination of those two beats anything Ford boys can make, including anything in the general tuner world.. So 14.28 is not impressive, especially that you have DOHC with dual length runners. You know, you could really ben...
- Mon Jan 29, 2007 1:41 pm
- Forum: Installation
- Topic: Sanity check....
- Replies: 2
- Views: 2769
TPS is connecting to
TPS is connecting to Megajolt! Here is what you do, leave the Megajolt and TPS out of equation. Work with these for now: VR, trigger wheel, EDIS, coil packs, and the wiring that goes between them. It will be enough to provide constant 10 BTDC timing when installed properly. After you have it wired t...
- Sun Jan 28, 2007 9:24 pm
- Forum: Assembly
- Topic: timing out connection error
- Replies: 8
- Views: 7566
Ahh!!! You like my rock
Ahh!!! You like my rock solid tuner too? Its a little out dated, but its ok, new version is just around the corner! Nah, if you were able to flash, and store/retrive config, then USB-2-Serial is not a cluprit... Most likely its a wrong configurator you using for the firmware. But it could also be co...
- Sat Jan 27, 2007 3:30 pm
- Forum: Operation
- Topic: TPS seems wrong way round
- Replies: 2
- Views: 3204
Looking at the above
<img src="http://www.picasso.org/mjlj/images/mjlj_v3_wiring.gif" width="640"></img> Looking at the above picture. You should swap the red 5V wire with the groud wire. So that the wire that you connect to the ground is now connected to megajolt, and the other wire will be connecte...
- Sat Jan 27, 2007 5:39 am
- Forum: Q&A
- Topic: TPI Small block Chevy
- Replies: 4
- Views: 4395
Hey, when you get your
Hey, when you get your setup, dont go crazy! Too much timing + stock cast pistons can equate to a cracked piston. Had it happen to me. Also, timing should be smooth. If you search the file library here, you'll find my 4.6 map, which had timing go to zero at no throttle. That was made so that I could...
- Sat Jan 20, 2007 4:31 am
- Forum: Q&A
- Topic: Will it die!
- Replies: 5
- Views: 3501
Mmmm, you guys are paranoid
Mmmm, you guys are paranoid about this a little too much. In the US every cop car is equipped with a laptop, mounted to a solid metal stand, which is then mounted to the frame. And those are body on frame cars, not some unibodies. Ive supported police departments, and almost never it was a bad hard ...
- Fri Jan 19, 2007 2:29 pm
- Forum: Q&A
- Topic: sources for 36-1 wheel
- Replies: 6
- Views: 5153
What are the part numbers
What are the part numbers for those wheels?
- Sun Jan 14, 2007 3:33 am
- Forum: Q&A
- Topic: Help please
- Replies: 4
- Views: 3918
I have no clue my friend, I
I have no clue my friend, I asked for you in a place that builds 2.0 DOHC, dont know if I will get a response. I suggest you look for "focus forums" on google, join forums and ask a question. Ford Focus had a 2.0L, and they know about old 2.0L engines. So you'll get your answer plus you'll...
- Sun Jan 14, 2007 3:02 am
- Forum: Assembly
- Topic: High vibration environment builds
- Replies: 3
- Views: 4937
Good advice, thanks. This
Good advice, thanks. This is for some high impact though, I can report, unfortunately, that after 120 mph or so crash my Megajolt worked perfectly. I span on wet highway last year, and went into metal bar rear first, after getting knocked out and a lot of oil smoke, it started right up and drove me ...
- Fri Jan 12, 2007 1:38 pm
- Forum: Operation
- Topic: Need some help uploading firmware.
- Replies: 8
- Views: 6345
You remember what you did
You remember what you did more than two years ago? Double check, maybe you do have a good CPU. Here is what you do, download a tuner for your board version, here are links: <a href="http://www.picasso.org/mjlj/?q=filestore2/download/709/mjtuner_0.2.2.1260_preview-Installer.exe">http://www....